Anyone else have to file down the cliffy scoop protector?
My one didn’t fit, metal on metal —- hitting the rear left uplift rod.
My one didn’t fit, metal on metal —- hitting the rear left uplift rod.
Pinball info
Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
JJP GNR Pinball
- Thread starter JustLikeMe
- Start date
The one I fitted was tight but sat down flush when done I didn’t have to file anything
^^^ yes it was flush but when I depressed the rod it was touching if rod was pushed forward... I think cliffys tolerances may be out now since JJP stuck loads of Mylar at the front of the scoop.
I’ve just checked Pinside and a few guys have found the same issue..
I’ve just checked Pinside and a few guys have found the same issue..
It must be hit and miss Chris, some guys are fine ...
Others unlucky- I’m always sh^t out of luck.....
Yes it’s very Mylar heavy round the scoop now
@CHRIS B PINBALLS nope took T-Nut out, under playfield I had a metal washer and nylon nut.
Now on playfield-side I have fitted Titan rubber washer then metal washer then the post Phil sent, I could trim the Titan down a bit, but it does not interfere with the ball and I hope the rubber washer will absorb some of the energy from the ball rather than the post alone transferring it to the playfield.
This 'fix' hides the chip.
Just hope its a 'fix'.
Turn the pop bumpers strength down too @ Julian
Limited Edition: #1011
Playfield Date: 19 Mar 2021
Build Date: Mar 2021
I found one screw in the cabinet haven't tracked down where it came from yet
I am missing the left hand screw that holds up the tweeter panel
I have a washer thats slightly deformed from over tightening of a ball rail
I did a nail test under the apron and was unable to make a dent
There is some substance on the left hand side of the backbox, maybe glue I don't know not tried to shift if with any cleaner yet.
Can't find anything loose under or above the playfield, the diverter seems to be positioned okay though there is a lot of left to right play anyone else noticed this is this by design?
Pinwoofer kit fitted and after setting it to the default recommended settings its remarkably better than the stock set up, as others have said a worthy upgrade.
Still to fit the cliffy's and 3 posts from Phil, my posts don't have any play in them so I might not bother.
Attachments
I had same screw floating. About too.. can’t find where it goes either!
the inside edge of the backbox where you have glue, mine is like a paint defect, looks like it has finger prints/ oil from hands but it won’t come off
the inside edge of the backbox where you have glue, mine is like a paint defect, looks like it has finger prints/ oil from hands but it won’t come off
If it’s a le then no further action is needed
But I would pop a rubber on the mini post on the upper playfield and you could turn down pop bumper strength there is no need for them to be so powerful
If it’s the ce then you should fit 2 posts i have explained this in a previous post
I can beat that Dave, boot prints on the metal backbox mounting plate in my Dialed in
. They really treat these machines with care during assembly at JJP. How many people walked past this and thought it was ok to leave it like that? I never mentioned it at the time, had more annoying things to deal with ( dead pixels on the main screen and phone lasted a day ).
Finally got round to setting mine up, number 991, all looks ok so started it up and played it, wow its really intense, absolutely no idea what i am doing yet but like it
Or over it, for that matter.
What you reckon, just made these up, silicon centre with rubber outer, just shy of 20mm?
Post and metal washer over the top...
.
Post and metal washer over the top...
.
Last edited:
Does cointaker ship to UK?
Their e-commerce site allows the transaction to come up with UK drop down when completing basket whilst their T&Cs states this:-
Their e-commerce site allows the transaction to come up with UK drop down when completing basket whilst their T&Cs states this:-
I’ve bought toppers from CoinTaker
My American Tour board is not working correctly within the test menu, not sure if its a software issue but here's what I observe if anyone can verify the same or different behaviour please;
LEDs #49..56 do not come on when selected in TEST -> LED TESTS -> ORDERED/GROUPED LED TEST
LEDs #57..64 turns on two lights (seems to be the ones above from #49..56) in TEST -> LED TESTS -> ORDERED/GROUPED LED TEST
I also noticed the GI Test doesn't show any lights when selecting TEST -> LED TESTS -> GI ONLY TEST
When selecting TEST -> LED TESTS -> ALL LED then all leds are illuminated
Thanks
Chris
LEDs #49..56 do not come on when selected in TEST -> LED TESTS -> ORDERED/GROUPED LED TEST
LEDs #57..64 turns on two lights (seems to be the ones above from #49..56) in TEST -> LED TESTS -> ORDERED/GROUPED LED TEST
I also noticed the GI Test doesn't show any lights when selecting TEST -> LED TESTS -> GI ONLY TEST
When selecting TEST -> LED TESTS -> ALL LED then all leds are illuminated
Thanks
Chris
I've pre-ordered the official GnR topper with Phil, I just think this will look great with the official blades James is getting + the LE art.
Great price too.
Phils gonna see if he can get the official blankets too.
I have a bit of sun coming in hitting the side of the pin and that bathroom towel just doesn't look right somehow ... lol
Great price too.
Phils gonna see if he can get the official blankets too.
I have a bit of sun coming in hitting the side of the pin and that bathroom towel just doesn't look right somehow ... lol
D
Deleted member 2463
You absolutely need the cliffy on the scoop - seen some horrific photos of scoop damage albeit from on locations games but as this scoop is core to gameplay it makes sense.
Sent from my iPhone using Tapatalk Pro
Sent from my iPhone using Tapatalk Pro
D
Deleted member 2463
Did you check the connectors ? I had a loose one that cause this also.
Sent from my iPhone using Tapatalk Pro
I've reseated a few connectors Neil but will systematically go round them all, cheers good to know it may be just a loose connection.
I’ve also ordered the official topper any links and prices to the official blades please.
Sent from my iPhone using Tapatalk
Just ask James matey, he’s getting them for most
Hey @Dave Bishop , I thought this was a brain fart originally as GnR drummer was originally zildjian but Frank Ferrer does use Sabian. Can you count me in please
Interested in everyone’s opinion on how the game plays
I can't comment as I haven't flipped a ball yet but it looks epic. Will let you know soon.
You'll be safe playing a game or two.
You should really do this to make sure you have a fully working pin matey after the steam boat from Bermuda Triangle.
Highly unlikely a few games will cause any damage without any protection.